5713 dual peripheral and power driver discontinued product for reference only this mini-dlp dual peripheral and power driver is a bipolar monolithic integrated circuit incorporating nor logic gates, high- current switching transistors, and transient suppression diodes on the same chip. the two output transistors are capable of simultaneously sinking 300 ma continuously at ambient temperatures of up to +70 c. in the off state, this driver will withstand at least 80 v. the UDN5713m dual driver is ideally suited for interface between low-level or high-level logic and high-current/high-voltage loads. typical applications include driving peripheral loads such as incandes- cent lamps, light-emitting diodes, memories, and heaters with a load current of up to 600 ma. the integral transient suppression diodes allow the use of these drivers with inductive loads such as relays, solenoids, or stepping motors without the need for discrete diodes. similar devices with four drivers per package are the 5703 and 5706. features n dtl/ttl/pmos/cmos compatible inputs n low input current n 300 ma continuous output current n stand-off voltage of 80 v dwg. no. a-9789 dual peripheral and power driver transient protected outputs 5713 always order by complete part number, e.g., UDN5713m . absolute maximum ratings supply voltage, v cc . . . . . . . . . . . . . . 7.0 v input voltage, v in . . . . . . . . . . . . . . . . . 30 v output off-state voltage, v off . . . . . . . . . . . . . . . . . . . . . . . . 80 v output on-state sink current, i on . . . . . . . . . . . . . . . . . . . . . . 600 ma suppression diode off-state voltage, v off . . . . . . . . . . . . . . . . . . . . . . . . 80 v suppression diode on-state current, i on . . . . . . . . . . . . . . . . . . . . . . 600 ma power dissipation at t a = 25 c, p d package . . . . . . . . . . . . . . . . . . . 1.5 w* each driver . . . . . . . . . . . . . . . . . 0.8 w operating free-air temperature range, t a . . . . . . . . . . . . . . . . . -20 c to +85 c storage temperature range, t s . . . . . . . . . . . . . . . . -55 c to +150 c *derate at the rate of 12.5 mw/ c above t a = 25 c. data sheet 29307b
5713 dual peripheral and power driver 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 min. nom. max. units supply voltage (v cc ) 4.75 5.0 5.25 v operating temperature range 0 +25 +85 c current into any output (on state) 300 ma recommended operating conditions electrical characteristics over operating temperature range (unless otherwise noted). test conditions limits driven other characteristic symbol temp. v cc input input output min. typ. max. units notes 1 input voltage v in(1) min 2.0 v 0 input voltage v in(0) min 0.8 v 0 input current at all inputs except strobe i in(0) max 0.4 v 30 v -50 -100 m a 2 0 input current at strobe i in(0) max 0.4 v 30 v -100 -200 m a 1 input current at all inputs except strobe i in(1) max 30 v 0 v 10 m a 2 1 input current at strobe i in(1) max 30 v 0 v 20 m a input clamp voltage v ik min -12 ma -1.5 v limits characteristic symbol test conditions min. typ. max. units notes turn-on delay time t pd0 v s = 70 v, r l = 465 w (10 watts), 200 500 ns 3 c l = 15 pf turn-off delay time t pd1 v s = 70 v, r l = 465 w (10 watts), 300 750 ns 3 c l = 15 pf switching characteristics at v cc = 5.0 v, t a = 25 c notes: 1. typical values are at v cc = 5.0 v, t a = 25 c. 2. each input tested separately. 3. voltage values shown in the test circuit waveforms are with respect to network ground terminal. 4. capacitance values specified include probe and test fixture capacitance. input pulse characteristics v in(0) = 0 v t f = 7 ns t p = 1 m s v in(1) = 3.5 v t r = 14 ns prr = 500 khz w copyright ? 1976, 1997, allegro microsystems, inc.
5713 dual peripheral and power driver electrical characteristics over operating temperature range (unless otherwise noted). test conditions limits driven other characteristic symbol temp. v cc input input output min. typ. max. units notes 1 output reverse current l off min 2.0 v 0 v 80 v 100 m a open 2.0 v 0 v 80 v 100 m a 0 output voltage v on min 0.8 v 0.8 v 150 ma 0.35 0.5 v min 0.8 v 0.8 v 300 ma 0.5 0.7 v diode leakage current i lk nom nom 0 v 0 v open 200 m a3 diode forward voltage drop v d nom nom v cc v cc 1.5 1.75 v 4 1 level supply current l cc(1) nom max 5.0 v 5.0 v 8.0 13 ma 1, 2 0 level supply current l cc(0) nom max 0 v 0 v 36 50 ma 1, 2 notes: 1. typical values are at v cc = 5.0 v, t a = 25 c. 2. per package. 3. diode leakage current measured at v r = 80 v. 4. diode forward voltage drop measured at i f = 300 ma. 5. capacitance values specified include probe and test fixture capacitance. dwg. no. a-9123a dwg. no. a-7628c
5713 dual peripheral and power driver 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 dimensions in millimeters (based on 1 = 25.4 mm) dimensions in inches 0.014 0.008 0.300 bsc dwg. ma-001-8a in 0.430 max 4 0.100 bsc 5 8 1 0.022 0.014 0.400 0.355 0.005 min 0.150 0.115 0.280 0.240 0.210 max 0.070 0.045 0.015 min 0.355 0.204 7.62 bsc dwg. ma-001-8a mm 10.92 max 4 10.16 9.02 2.54 bsc 0.13 min 3.81 2.93 5 8 1 7.11 6.10 5.33 max 1.77 1.15 0.39 min 0.558 0.356 notes: 1. lead thickness is measured at seating plane or below. 2. lead spacing tolerance is non-cumulative. 3. exact body and lead configuration at vendors option within limits shown. allegro microsystems, inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the design of its products. the information included herein is believed to be accurate and reliable. however, allegro microsystems, inc. assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties which may result from its use.
|
